The Short Version: How to Tell If a Light Switch Is Bad — and the Ordering Mistakes That Cost Me $4,200
If your lights won't turn on but the breaker is live, test in this order: swap the switch with a known-good one, check the neutral at the fixture, then meter the hot leg. Roughly 70% of "dead switch" calls I've handled were the switch itself — the rest were loose neutrals, backstabbed connections that had worked loose, or a dimmer that wasn't rated for the load.
Fifteen minutes of testing, in that order, will save you a return trip. That part is straightforward. The expensive part comes later, and it's the reason I'm writing this: most of my wasted budget didn't happen during diagnosis. It happened after — during ordering and installation.
I've spent about $4,200 on wrong-part orders and re-do installs over the past seven years of facility maintenance work. Every one of those mistakes was preventable with a 10-minute check that I skipped because I was in a hurry.
Why You Should Trust This Number
I'm the person who orders the parts when a fixture fails or a contractor flags a gap. I've processed roughly 300 electrical and lighting orders since 2018, ranging from a single pilot light to full lighting control retrofits. I've documented every order that came back wrong. There's a spreadsheet. No, I'm not proud of it.
Two mistakes still bother me:
- September 2022: I ordered 40 indicator lights for our pump panel without confirming the lamp voltage. The old units were 120V. The replacements were 24V. The supplier wouldn't take back special-order hardware. Cost: $610 in dead stock plus a three-day delay while I sourced replacements from another distributor. The panel ran blind for two shifts.
- Q1 2024: I nearly repeated the same mistake with power supplies. Different product line, same assumption that "24V is 24V." Our new checklist caught it at the packing-slip stage because it forced me to verify the nameplate spec against the purchase order. That check takes 90 seconds. The avoided reorder would have cost roughly $1,100.
Everyone told me to always cross-check the voltage against the nameplate. I only believed it after September 2022. That's the honest version.
The Three Mistakes That Eat Most of the Budget
1. Ordering a replacement before confirming the exact spec
When you're replacing a component, the part number on the old unit is a starting point, not an answer. Cross-reference it against the current catalog.
Example: I needed pilot lights for a control panel. The old units had been in service since the late 1990s — the Eaton pilot light 10250T172-2 in our spare bin was the closest match, but the current catalog listed a different lens color and voltage range. If I'd ordered on the old number alone, I would have received lamps rated for a different circuit. That's a small-dollar mistake in isolation. It's not a small downtime mistake — you can't run a panel with dark indicators.
The fix: pull the nameplate data from the failed component, cross-reference it against the current specification sheet (Eaton's are detailed and available at eaton.com), and write the voltage, amperage, and termination style directly onto the purchase order. If the sheet is ambiguous, call the manufacturer. Don't guess.
2. Assuming all power supplies are interchangeable
I nearly learned this the hard way with an Eaton PSG480F24RM power supply. The model number looks specific, but the spec sheet still has to match your existing circuit. Input voltage range, output current, and physical dimensions all have to line up with what's already in the enclosure.
Checklist:
- Input voltage range (a 480V feed needs a matching input rating)
- Output voltage and current (24V/4A is not the same as 24V/10A)
- Mounting and physical dimensions
- Compatibility with the existing power supply enclosure and wiring method
If any of those four items isn't confirmed on paper, don't submit the order. Personally, I'd rather spend 90 seconds on the nameplate than three days on the phone with a supplier who won't accept the return.
3. Ordering fixtures without checking the site first
This applies to outdoor and indoor work equally, and both have bitten me.
On the outdoor side: I've ordered yard spotlights that didn't fit existing junction boxes and once received a fixture rated for the wrong area classification. Both were catalog mismatches that a 10-minute site photo and a spec sheet comparison would have caught.
On the indoor side: chandelier hanging is a different kind of risk. Before you specify the fixture, confirm the ceiling structure, anchor capacity, and clearance. I watched a crew hang an 80-pound fixture from a box rated for 35 pounds. It held for six months, then it didn't. Nobody was hurt. The repair cost more than the fixture.
The prevention step is boring: photograph the mounting location, measure the box, confirm the anchor type, check the fixture weight against the anchor rating. If the spec sheet doesn't give you the answer, call the manufacturer. In my experience, that call takes less time than the return.
What This Advice Doesn't Cover
My experience is based on roughly 300 orders in commercial and light industrial facilities — schools, warehouses, a few office build-outs. If you're working with heavy industrial switchgear or high-voltage distribution, your failure modes are different and your tolerance for error is much lower. For those projects, you need a second reviewer and probably a stamped submittal. I can't speak to that world.
Also, this was accurate as of early 2025. Part numbers change, catalogs update, and some of what I learned in 2019 has already been superseded by newer product lines. Verify current specs at the manufacturer's site. Don't take my word for it.
The $4,200 number is real. The lesson is cheaper than the mistake: check the spec, check the site, then check it again. Prevention costs minutes. Redo costs days.